Xtramus DApps-TAP V1.3 Manual de usuario

DApps-TAP Utility User’s Manual USM Ver 1.3

2.4. NuDOG-301C Interface Ports NuDOG-301C Hardware Overview A LEDs LEDs that displays NuDOG-301C’s status. B Mini-USB Port* 5 Pin Mini-B Receptac

2.5. NuDOG-301C LED Status LED Status Description Green Blinking Power is ON and working properly Power/Fail Yellow Blinking System failed USB Gre

3. NuDOG-801 Descriptions 3.1. NuDOG-801 OVERVIEW NuDOG-801 is a handheld device with two 10 Gigabit SFP+ Ports for Ethernet testing. The main functi

3.2. Features & Advantages of NuDOG-801 ¾ Hardware based wirespeed streams generation, analysis, and NIC ¾ High precision performance for measuri

TAP/Loopback Mode TAP Mode Loopback Mode In TAP mode, NuDOG-801 can monitor any data that flows through it. Network TAP is a method of monitoring n

3.4. NuDOG-801 Interface Ports NuDOG-801C Hardware Overview A LEDs LEDs that displays NuDOG-801C’s status. B Mini-USB Port* 5 Pin Mini-B Receptacl

3.5. NuDOG-801 LED Status LED Status Description Green Blinking Power is ON and working properly Power/Fail Yellow Blinking System failed USB Gree

4. NuDOG-101T Descriptions 4.1. NuDOG-101T OVERVIEW NuDOG-101T is a handheld device with two ports for Ethernet testing. The main functions of NuDOG-

4.2. Features & Advantages of NuDOG-101T ¾ Hardware based wirespeed streams generation, analysis, network TAP and NIC ¾ High precision performanc

TAP/Loopback Mode TAP Mode Loopback Mode In TAP mode, NuDOG-101T can monitor any data that flows through it. Network TAP is a method of monitoring

Foreword Copyright Copyright © 2012 Xtramus Technologies, all rights reserved. The information contained in this document is the property of Xtramus

4.4. NuDOG-101T Interface Ports NuDOG-101T Hardware Overview A Mini-USB Port for connecting NuDOG-101T to PC or for power supply. B LEDs that displa

4.5. NuDOG-101T LED Status LED Status Description Green Blinking Power is ON and working properly Power Yellow Blinking System failed USB Green Bl

5. Installing/Uninstalling DApps-TAP Please follow the steps down below to install DApps-TAP. Also, please note that DO NOT connect your NuDOG-301C,

Installing DApps-TAP 4. Click “I accept the terms in the license agreement”, and click “Next” to continue. 5. You can input Username and Organiza

Installing DApps-TAP 7. DApps-TAP InstallShield Wizard will start installing momentarily. Click “Install” button to continue. 8. InstallShield

You can uninstall DApps-TAP by: Uninstalling DApps-TAP • Click Start Æ Programs Æ Xtramus Æ DApps-TAP Æ Uninstall DApps-TAP. • Go to the Cont

6. DApps-TAP Overview 6.1. Starting DApps-TAP Before starting DApps-TAP, your PC and NuDOG-301C/NuDOG-801/NuDOG-101T shall be connected properly. The

If your PC is not connected with NuDOG-301C/801/101T, you can still run DApps-TAP under Demo Mode. Almost all DApps-TAP’s functions are available un

6.3. DApps-TAP Overview DApps-TAP Functions Overview A Menu Bar The Menu Bar allows you to make settings about task criteria, view Counter window, l

7. DApps-TAP Functions 7.1. Menu Bar DApps-TAP Menu Bar includes configuration options such as File, Config, Statistics, Control, Languages, and Hel

Revision History Date Ver Software History 2011/12/15 1.0 V1.1b002 First draft version 2012/08/06 1.1 V1.1b004 1. Add NuDOG-801. (Page 6, 22,

7.1.2. Config 7.1.2.1. Run Mode Run Mode Analysis Mode All the function of DApps-TAP is available. Counter Mode The packets capture function and

7.1.2.3. Frame gap for USB transferring Frame gap for USB transferring Four modes are available in Frame gap for USB transferring: Fast, Medium, Slow

7.1.3. Statistics 7.1.3.1. Counter Window Counter Window Click the Save button to save the current counter data. The Update button allows you to

7.1.3.2. Alarm Report This window will warn you about the over high threshold of the parameter chosen in port configuration, for more detail about h

7.1.4. Control 7.1.4.1. Capture Buffer Capture Buffer Standard Mode Active capture buffer (built-in memory) mode for maximum 2K size packets. Jumbo

7.1.6. Help Help About DApps-TAP An “About” window will pop up and show detailed system information. System Requirements A “System Requirements

7.2. Tool Bar The Tool Bar contains buttons that allow you to reconnect NuDOG-301C/801/101T, view Counter, view USC A/B, view Chart and Configure Po

7.2.3. USC A & USC B USC A/B ¾ Allows you to save the data of this window. ¾ Clear all the data of this window.¾ Hide all the data that is

7.2.4. Chart Chart_Line Click the Chart button to pop up the Chart window shown above. From A bar, you can click the button to see Packets status

Chart_Pie Click the button as shown in A to view the pie chart in B field. The pie chart shows the percentage of each captured packet size duri

Table of Contents Foreword ...

Chart_Bar Click the button as shown in A to view the bar chart in B field. The Bar chart shows the rate of network event counts from Port A to

7.2.5. Port AB Port AB_Media Type Click the Port AB button to pop up the Port AB configuration interface. In this interface, you can set the Media

Port AB_Capture Criteria In the Protocol interface, If you click the Capture all packets function, you will enable the DApps-TAP to capture all pac

Port AB_Loopback If you choose the TAP mode on Loopback interface, the NuDOG-301C, NuDOG-801 and NuDOG-101T operates like a hardware device that p

Port AB_Alarm In the Alarm interface, you can choose the alarm threshold to be displayed on the alarm report. When the check box is ticked as, th

7.3. System Info/Configuration List The System Info/Configuration List allows you to view system information and making port configurations. 45E-

7.3.1. System Information By clicking the System Information on the System Info/Configuration List, the System Information screen will be shown on t

7.3.2. Port A & Port B Media Type, Capture Criteria, Loopback and Alarm By clicking the Port A & Port B on the System Info/Configuration Lis

7.3.3. Port A / Port B 7.3.3.1. Media Type, Capture Criteria, Loopback and Alarm By clicking the Port A or Port B on the System Info/Configuration L

7.3.3.3. Capture Buffer Mode and Capture Forward Mode A: This field shows the number of packets and number of captured packets. B: If you set Captur

7.3.3.3. Capture Buffer Mode and Capture Forward Mode...49 7.3.4. Report: USC A/B ...

7.4. Control Buttons/ Operating Status Icon 7.4.1. For TAP mode The Control Buttons allow you to start/stop tasks, and the Operating Status Icon ind

8. Appendix – Other Utility Softwares for NuDOG-301C/801/101T There are several other optional utility softwares for NuDOG-301C/801/101T for differen

Note: Information and specifications contained in this document are subject to change without notice. All products and company

1. General Description of DApps-TAP For NuDOG-301C, NuDOG-801 and NuDOG-101T, all data streams between two network ports can be duplicated and sent t

2. NuDOG-301C Descriptions 2.1. NuDOG-301C Overview NuDOG-301C is a handheld device with two Gigabit ports for Ethernet testing. The main functions o

2.2. Features & Advantages of NuDOG-301C ¾ Hardware based wirespeed streams generation, analysis, network TAP and NIC ¾ High precision performanc

TAP/Loopback Mode TAP Mode Loopback Mode In TAP mode, NuDOG-301C can monitor any data that flows through it. Network TAP is a method of monitorin