Xtramus NuTAP-S61 V1.2 Manual de usuario descargar pdf (Pagina 28)

B. NuTAP-S61 HyperTerminal Command – counter

Command Descriptions – counter

The counter show command allows you to view all NuTAP-S61’s counter report, as

well as hardware temperature. You can also add additional commands behind the

counter show command as listed down below:

The counter show usc [a0 | a1] [group=0 | group=1] command allows you

to view NuTAP-S61’s USC (Universal Stream Counter) report of its Network

Port (A0/A1) and the USC group. For example, to view the USC in USC

group 0 for Network Port A0, please input the command “counter show usc

a0 group=0”.

show

usc

configure

The counter show configure command allows you to view

USC’s settings.

clear

The counter clear command allows you to clear all counters.

show

The refreshtime show command allows you to view the refresh time for the

report.

refreshtime

set

The refreshtime set command allows you to set the refresh time (in

seconds) for the report.

The counter setusc command allows you to configure NuTAP-S61’s USC (Universal

Stream Counter) settings. Please refer to the sections down below for detailed

descriptions. Also, to view command lists for USC settings, you can input “counter

help setusc”.

The counter setusc [a0 | a1] [group=0 | group=1] baseaddress [da

| sa | vid | mpls | dip | sip | dp | sp | vlancos | vid&vlancos] <value>

command allows you to change the specific base address for

NuTAP-S61’s certain Network Port (A0/A1) and the USC group.

Please refer to the table down below for command initial reference:

• DA: Destination Address

• SA: Source Address

• VID: VLAN ID

• MPLS: Multi-Protocol Label

Switch

• DIP: Destination IP Address

• SIP: Source IP Address

• DP: Destination Port

• SP: Source Port

• VLANCOS: VLAN Class of

Service

• VID&VLANCOS: VLAN ID and

VLAN Class of Service

baseaddress

For example, to set the USC in source IP address of USC group 0 for

Network Port A0 to 192.168.1.1, please input the command “counter

setusc a0 group=0 baseaddress sip 192.168.001.001”.

The setusc [a0 | a1] [group=0 | group=1] mode [normal | jitter]

command allows to change the mode for NuTAP-S61’s certain

Network Port (A0/A1) and the USC group. There are two modes

available here:

• Normal: The USC will run

under normal mode.

• Jitter: The USC will run under

jitter mode.

mode

For example, to set the mode of USC group 0 for Network Port A0 to

normal, please input the command “counter setusc a0 group=0

mode normal”.

counter

setusc

enable/disable

The setusc [a0 | a1] [group=0 | group=1] [enable | disable]

command allows you to enable/disable NuTAP-S61’s certain Network

Port (A0/A1) and the USC group. For example, to enable USC group

0 for Network Port A0, please input the command “counter setusc a0

group=0 enable”.

E-mail: [email protected]

Website: www.Xtramus.com

XTRAMUS TECHNOLOGIES

1 2 ... 23 24 25 26 27 28 29 30 31 32 33 ... 74 75

Comentarios a estos manuales

Sin comentarios

Xtramus NuTAP-S61 V1.2 Manual de usuario Pagina 28

Comentarios a estos manuales

Relacionado con productos y manuales para Hardware Xtramus NuTAP-S61 V1.2